Skip to Content

What is the Bolt Pattern on a 2010 Ford F150?

The bolt pattern on your 2010 Ford F150 is 6×135 mm. This bolt pattern uses 5 lug nuts for securing your wheels. The lug nut is a standard sized nut that has a diameter of about 6 mm. The “hex” in the bolt pattern refers to the diameter of the top of the nut. The thread size refers to the size of the shaft and the distance between the threads.

While you can purchase aftermarket wheels and tires for your 2010 Ford F150, you should keep your vehicle’s original bolt pattern intact. By following the stock specs, you can enhance your vehicle’s appearance without buying expensive aftermarket parts. However, it is advisable to stick to the stock wheel specs if you want to upgrade your truck’s performance. Additionally, using aftermarket wheels can affect your fuel consumption and speedometer measurements. In some states, you can be fined if you don’t comply with safety regulations.

What Size Rims Will Fit on a 2010 Ford F150?

When shopping for rims for your truck, make sure to pay close attention to the bolt pattern of your F-150. While most rims will work on different vehicles, not all are bolt-on for your F-150. Here’s a guide to F-150 lug patterns. The bolt pattern for your truck is 6x135mm. Generally, 6×139 rims will fit on your truck, but they will have a gap of 1.5 to two inches on each side.

In general, the standard size of tires for your Ford F-150 is LT245/70R17. If your truck has a 5.4-liter V8, you’ll need to install a tire that’s the same size. This means choosing a rim that has the same bolt pattern as the original and has the same size locking hubs. You can also find the lug nut diameter online or in the manufacturer’s manual.

While choosing your rims, you should consider the mp, weight, and wheelbase of your F-150. Buying larger rims will increase your vehicle’s momentum, but will also lower your fuel efficiency. If you want to purchase larger rims, make sure to consult your car’s manual to determine the correct size. It is not uncommon to find that different models of the same vehicle use different tire sizes.

READ ALSO:  Where Can I Rent a Full Size Pickup Truck?

What Year F150 Have 6X135 Bolt Pattern?

The question: What Year Ford F150s Have a 6X135 bolt pattern? Generally speaking, there are 5 models with this pattern. The bolt pattern is 6×5.3 inches, which is equivalent to six lug holes on a circle with a diameter of 135 mm. The bolt pattern is interchangeable between models, so the bolt pattern on your F150 will be the same as it is on a Ford truck from 2004 to 2015.

If you want to swap out your F150’s wheels for some other style, you can do so easily. The bolt pattern on Ford trucks is usually circular, with the center of the wheel lugs and bolt holes intersecting. You can buy adapters to change the lug pattern in your F-150, so that you can put a different wheel on it. Located in Decatur, Alabama, Sam Leman Ford Parts Center carries everything you need to swap out your wheels.

What Vehicles Use 6X135 Bolt Pattern?

If you have an F-150, chances are you have a 6×135 bolt pattern. This is the pattern that uses a 3.5 inch bolt, and will not fit a 5×114.3 bolt pattern. Similarly, the 6×139 bolt pattern is not compatible with a 5×114.3 bolt pattern. You should find the correct bolt pattern for your vehicle by identifying its sticker plate.

To determine which vehicle’s wheel and tire hub have 6X135 bolt patterns, you can measure the diameter of the wheel hub. Some of these bolt patterns have very close diameters. You can use a bolt pattern gauge to verify the bolt hole patterns. For more information, check out the online database. You can find this information on most automotive forums. You can also find this information in a specialized truck part database.

Will 2016 F150 Wheels Fit a 2010 F150?

New F150 truck buyers frequently want to customize their rides by installing new tires and wheels. Choosing the right wheels and offsets can be tricky, so we’ve put together an informative video. Watch it now to learn more about wheel offsets. Then, purchase the wheels that best match your truck. You can also check your vehicle’s owner’s manual to see which wheel sizes are recommended for which truck.

A wheel’s offset is measured in millimeters. A positive offset would push the wheel inward while a negative offset would push it outward. Different years of the F150 come with different wheel sizes, so knowing what size you have will be helpful in getting the right fit. Listed below are three different options. You can also find out the wheel offset for a 2010 F150.

READ ALSO:  How to Remove a Radio From a Ford F150?

A 20-inch rim may require minor modifications on the truck. You can find adapters for the bolt pattern at local auto parts stores in Decatur. A set of wheel adapters can also be purchased at Sam Leman Ford Parts Center. Using this kit will ensure your new F150 wheels and tires are compatible with your truck. Just make sure to get them installed by a professional!

What Size Wheels Can I Put on My F150?

When it comes to wheel sizes, the 2010 Ford F-150 comes with a factory-specified rim size. There are some variations in wheel size from year to year, but there are some basic rules to follow. If you want to get the best look from your new wheels, make sure to check the offset. It’s easy to check the offset by looking at the rim’s mounting plate and spoke back. The offset should be printed as an “ET” or a combination of letters.

Changing wheel size won’t affect the ride quality, but it’ll improve your truck’s look. A 35″ tire fitted onto an 18.9″ rim would require a leveling kit and some plastic trimming. A 35’s size will fit on a 18×10 -44 rim with some minor plastic trimming. If you want to put larger tires on the F150, make sure the wheels have enough clearance for the new wheels.

What Size Tires are on a 2010 Ford F150 XLT?

If you’ve just purchased a new truck, you may be wondering, “What Size Tires are on a 2010 Ford-150 XLT?” The answer depends on the rims that came with your truck. In other words, if you bought 16-inch rims for your truck, you’ll need to choose a different size of tire. But do not worry, there’s a quick fix for this problem.

The LT in the tire number line stands for Light Trucks. The P or C stands for passenger and commercial use vehicles. The 17 is the diameter of the wheel, which is measured from one end to the other. If you’re wondering about the size of tire you need to buy, you should know that it’s 17 inches in diameter. Make sure the tire you buy is compatible with the wheels. The letters BSW and OWL stand for Black Sidewall and Outlined White Letters.

READ ALSO:  How to Win Terry's Truck?

You should replace your tires every five years, or at least after 57,000 miles. This helps protect your vehicle’s rubber and steel/kevlar belts from the elements. Although these materials are sturdy and can withstand the rigors of off-road use and virginia snowstorms, they eventually break down. However, there’s no harm in replacing them with original Ford equipment tires. There are also some drivers who prefer different tires or a combination of both.

What Lug Pattern is a 2011 F150?

If you are wondering what lug pattern your 2011 Ford F150 has, you can start by reading your owner’s manual. Then, you can get the measuring instruments and begin the process of finding the proper lug pattern. You can also get a measuring tape or a Vernier caliper to help you. Every pickup rim has measuring holes, so you can use one of these to take a measurement.

The bolt pattern is the circle formed by the centers of the lugs and bolt holes on the wheels. This information is in the owner’s manual and on the wheel size charts. Using the wrong size wheel will cause uneven load distribution and a reduced turning radius. Getting the wrong bolt pattern will also make your new wheelset impossible to fit. Also, if your lug pattern is the same as the wheels on your Ford, then you cannot use low-profile tires.

Learn More Here:

1.) Latest on Ford F150

2.) Ford F Series – Wikipedia

3.) Official Ford Support

4.) F150 History