If your truck has a damaged steering column, it may be a simple job to replace it yourself. There are a few simple steps you should take to do it properly. First, disconnect the wires from the column. They are attached to the steering shaft, which must be separated from the intermediate shaft to do this. Next, disconnect the steering shaft from the steering box. This will allow you to remove the steering column and inspect the parts inside.
Next, locate the steering column and shifter cables. You may have to remove the transmission cable if your truck is equipped with a manual transmission. Make sure to locate this cable so you don’t break it. Then, remove the two nuts holding the steering column in place. Then, insert new cables and connectors. Repeat the process for the other side of the steering column. Then, reinstall the steering column and shifter.
How Do You Change a Steering Column?
Before attempting to replace your steering column, disassemble it. It is usually held in place by four screws at the base. To remove the steering column, you must first remove the steering wheel. Then, you can use a steering wheel puller to remove the lock plate and retaining ring. You will also need to remove the key switch and turn signal cancel cam. Finally, you will need to remove the plastic collar that holds the column’s pivot pins.
Once you have removed the steering shaft, you can remove the steering column. If your steering column is damaged, you may want to have a mechanic replace it for you. Once you have separated the steering shaft from the intermediate shaft, you can easily remove the steering column. Then, you can remove the steering column itself to inspect the parts and to change any damaged parts. Make sure that the steering shaft is disconnected from the steering box.
How Do You Remove the Steering Column?
How Do You Remove the Steering Column from a Chevy Truck? Here’s how. First, unscrew the two screws on the steering brace. You should then be able to twist the steering wheel a quarter turn to free it. After this, you can remove the steering column from your car. Follow these steps for the next steps to removing your steering column. They’re fairly straightforward.
The next step is to loosen the steering column nuts that connect the steering shaft to the steering gear box. You can also try to separate the steering shaft from the intermediate shaft. This step is important in removing the steering column because you might accidentally damage it during the process. Once the steering shaft is separated from the steering gear box, you can pull the steering column out. Make sure that you keep the steering wheel level as you remove the steering column.
Next, make sure to mark the shift rods on both sides of the column. The one closest to the firewall has a 1/2″ nut and C-clip. Swing the rods away from the steering column towards the engine. Then, reach into the DS wheel well and remove the plate inside the inner fender. Finally, remove the rag joint from the steering box shaft using a 12-point 7/16-inch socket.
How Much Does It Cost to Change Steering Column?
When replacing a steering column on a Chevrolet truck, there are a few different factors to consider. One of these factors is the type of steering technology attached to the column. More advanced vehicles require a more powerful steering system. A Mercedes steering column may cost upwards of $900. Another factor affecting cost is the type of steering tech. Today’s steering shafts can come with a variety of gadgets attached, making replacement more difficult.
Once you’ve decided to change the steering column on your Chevrolet truck, the mechanic will first remove the existing steering column. This involves unscrewing and lifting the old steering column. He will then disconnect any wires connected to the steering wheel. Afterwards, he will connect the new steering column to the existing screw holes and secure it with bolts. After this, he will install the new steering column and mount it to the dashboard. Then, he will reconnect any cables that have been disconnected.
In addition to these factors, the steering column is a significant component of the power steering system. When it breaks down or wears out, it will inhibit the steering wheel’s ability to return to its original center. This means that driving your car is compromised and the safety of passengers is at stake. If the steering column is not replaced, further problems can arise. Further repairs will only raise the overall cost of replacement.
Can You Drive with a Broken Steering Column?
When your Chevy Truck’s steering column fails, it’s imperative to have it replaced right away. This important part controls the vehicle’s steering and may cause your car to become unsafe to drive. Even if you can still drive, a broken steering column can make driving very difficult and even risk your life. Here are some signs that your steering column might be damaged. Here’s what to do if you suspect your steering column is damaged.
If you notice a binding steering wheel or one that doesn’t return to center after a turn, it’s likely your steering column isn’t working properly. It’s also possible that your column may be loose or tilted. Either way, this will make steering difficult, and you’ll probably experience a swerving motion even on a straight course.
What Causes Steering Column to Go Bad?
In modern vehicles, the steering column is connected to the suspension. Its purpose is to transfer torque power from the steering wheel to a steering shaft and pinion. In turn, the wheel turns according to the direction that the steering wheel is pointing. However, when the steering column malfunctions, you may experience a loss of steering control. If you suspect that your column is faulty, here are a few possible causes.
Noise coming from the steering column is usually a result of a worn or damaged intermediate steering shaft. Usually, the steering shaft moves slightly when the truck body flexes on its frame. The steering box and column are attached to the frame, and they are linked by a splined slip joint. The shaft is lubricated with grease in the slip part, which gradually moves to one end. As the shaft moves, the grease gradually creeps to the end and causes the noise. Symptoms of a bad steering shaft are often a noise that starts at 60,000 or more miles, although it may start earlier.
If you notice vibrations from the steering wheel, the wheels could be misaligned. You might also have damaged axles, or your steering system might be out of balance. If you notice this issue, you need to see a professional mechanic to determine the cause. In some cases, you may be able to repair the problem yourself. Often, however, a minor steering wheel problem will require a mechanic to replace the entire column, but it is worth it to avoid a costly repair.
How Do You Secure a Steering Column?
When you turn the key, you will receive a message from the car’s system stating that the steering column is locked. It’s a sign that thieves have a high-risk target in the steering column. To solve the problem, you can secure the steering column with a steering column lock. The lock will prevent the steering wheel from turning and will also protect the ignition switch.
Learn More Here:
3.) Best Trucks